Surface Properties and Wear Resistance of Injectable and Computer-Aided Design/Computer Aided Manufacturing–Milled Resin Composite Thin Occlusal Veneers

European Journal of Dentistry · 4 authors, 4 centres

AI SUMMARY

FIDELITY 100%

This summary was generated by AI from a single paper. It has not been reviewed by a clinician and is not clinical advice. Verify against the source before acting on it.

AGENT 01 · STRUCTURED SUMMARY

TRACE TO SOURCE

“

TL;DR

Specimens were subjected to 500,000 cycles of thermomechanical loading to simulate 2 years of clinical service.

Full summary

111 CHARS

Specimens were subjected to 500,000 cycles of thermomechanical loading to simulate 2 years of clinical service.

STUDY TYPE

other

SPECIALTY

preclinical research

SUMMARISED BY

AI pipeline

FIDELITY CHECK

100% · A

ORIGINAL PAPER

PMC10569885

Surface Properties and Wear Resistance of Injectable and Computer-Aided Design/Computer Aided Manufacturing–Milled Resin Composite Thin Occlusal Veneers

European Journal of Dentistry

READ THE FULL PAPER

ABSTRACT

Objectives This study was conducted to investigate the microhardness, surface roughness (Ra), and wear behavior of thin occlusal veneers (TOV) fabricated from different injectable composite materials and compare them to a Computer-Aided Design (CAD)/Computer-Aided Manufacturing (CAM) resin-based material. Materials and Methods A 1-mm occusal veneer preparation was done in a mandibular right second molar typodont tooth. The prepared model was duplicated to fabricate 32 replicas and divided into four groups ( n = 8). Standard TOV were fabricated either indirectly from Cerasmart blocks, Cerasmart, GC (CS), or directly from Beautifil Injectable X, Shofu (BF), G-ænial Universal injectable, GC (GU), or SonicFill 2, Kerr (SF) using the injection molding technique. All the specimens were subjected to both thermomechanical cyclic loading (TMC) in a chewing simulator. Wear measurement was conducted by three-dimensional (3D) scanning of the veneered models before and after TMC, and the difference in the volume of the sample was recorded as the volumetric material loss due to wear. Ra before and after TMC and Vickers microhardness (VHN) of the tested materials were measured using standardized samples ( n = 8). Representative samples from each group were investigated under a stereomicroscope and a scanning electron microscope. Statistical Analysis One-way analysis of variance (ANOVA) was applied to detect the effect of material on VHN and wear. Two-way ANOVA was utilized to examine the impact of material and TMC on Ra. Multiple comparisons between the groups were conducted using Tukey's post hoc test ( α = 0.05). The Pearson's correlation coefficient was used to determine the relationship between hardness and wear and between roughness and wear ( α = 0.05). Results CS exhibited the highest mean VHN ( p ≤ 0.001), followed by GU and SF which were statistically similar ( p = 0.883) but significantly higher than BF ( p < 0.001). After TMC, GU revealed the lowest Ra and volumetric wear (VW), followed by CS, BF, and SF ( p < 0.5). A highly significant correlation existed between Ra and VW ( p = 0.001, R 2 = 0.9803). Conclusion The effect of TMC on the surface properties and wear resistance of the investigated TOV is material-dependent. GU injectable TOV are less influenced by TMC than CS milled TOV. In contrast, BF and SF demonstrated significant VW and Ra which might limit their clinical use as TOV.

CITATION EXPORT

Nesrine A. Elsahn, Hatem M. El-Damanhoury, Zainab Shirazi et al.. Surface Properties and Wear Resistance of Injectable and Computer-Aided Design/Computer Aided Manufacturing–Milled Resin Composite Thin Occlusal Veneers. European Journal of Dentistry. (2022). https://doi.org/10.1055/s-0042-1750769

AUTHORS

4 · 4 CENTRES

Nesrine A. Elsahn, Hatem M. El-Damanhoury, Zainab Shirazi, Abdul Rahman M. Saleh

1Department of Clinical Sciences, College of Dentistry, Ajman University, Ajman, United Arab Emirates
2Center of Medical and Bio-allied Health Sciences Research, Ajman University, Ajman, United Arab Emirates
3Department of Operative Dentistry, Faculty of Dentistry, Cairo University, Cairo, Egypt
4Department of Preventive and Restorative Dentistry, College of Dental Medicine, University of Sharjah, Sharjah, United Arab Emirates